New Combine Added to Roster

Stockton & Copperopolis combine Number 16 photographed just outside Copperopolis.

Due to rising lease costs, the S&C management decided to purchase its own combine for trains running on the Milton branch. It is very similar to those used successfully on the Virginia & Truckee Railroad and is expected to give good service here.
     In reality, for several years now I have not had S&C lettered coaches for the Milton branch and have been using some of my old Moraga Springs Northern equipment. A note that a member of the EarlyRail io-group list wanted to sell an old Central Lines kit prompted the replacement. The Central Lines kits were made in the 1950s, perhaps into the '60s and were crude compared to today's standards. For example, the roof was a milled piece of wood which you were expected to shape into something resembling a clerestory roof. I had noticed a 3D printed roof offered by Eight-Wheeler Models and thought it might be a good substitute.
   

The 1950s Central Lines box with the "high-tech" (for then) roof. The 3D
printed roof looks a lot better.

The point of the kit is that it had very good sides apparently molded in plastic with decent detail. The roof was designed to fit on Model Die Casting Overland passenger cars but I figured that it could be shortened. The trucks were another item listed on Shapeways which I had used on my Long Caboose project a while back.
     I started putting the kit together per the instructions. The platform steps were all right but the end railings leaved something to be desired so I substituted Cal-Scale railings. Truss rods are of .015 inch fishing line. Before I ordered the roof, I checked the width of the MDC cars and they were the same as the Central Lines Kit. Shortening the roof consisted of cutting a piece out of its center and gluing it back with some reinforcement on the underside. Some Testors patching putty was used to smooth out the joints. It did not come with the clerestory windows so I cut those out of some stiff cardboard and glued them in.Since the original kit roof was straight with straight letterboard extensions, I glued a piece of styrene to the sides and shaped the ends to fit the new roof. Roof detail is from Grandt Line parts.
     The lettering was based on the prototype V&T 16 in the California State Railroad Museum. I tried something a bit different for the roof finish this time. In the nineteenth century, the roofing on most passenger cars consisted of sheets of terne metal crimped together. To simulate this, I applied a decal which had lines simulating the standing seams of the prototype. The artwork was borrowed from my friend, John Ott, who developed it for one of his cars. I think it looks pretty nice. Thanks, John.

The Depot at Farmington

Although the steps seem to be floating in air, when scenicking is done, they will be flush with the top of the ties. An earth berm will run from the train order signal past the privy .

The Farmington Depot is now complete except for scenicking. It was an interesting project using customary model building techniques combined with laser cutting and 3D printing.

The 3D printed casings fit perfectly around the Tichy
window castings.

The depot has some unusual casing details around the upper part of the window. I drew up some 3D drawings of it sized to fit the Tichy windows and doors I was using and sent them to Shapeways to have the casings printed.
     In the prototype photo shown in my last blog (http://sandcrr.blogspot.com/2018/05/laser-cutting-and-depots.html), you can just barely see the end of a ladder peeking out from behind the depot. This was normally used to access the roof and it seems that most of the Southern Pacific depots had one. I relocated mine to the end of the building so someone might actually see it. The small "bridge" on the platform's end was used to span the gap between the platform and a car to aid in loading or unloading of it.
     Adjacent to the depot is something one sees at almost all of the depot photos, the privy. This one is a standard SP design and is made from two of the Tichy outhouse kits. The lattice work around the privy is also from Tichy.

The privy at Farmington and the model privy. It is a close copy. I realize that the model roof has a steeper pitch and the lattice work is square rather than on an angle. These were modeling considerations I took into account to get the "feel" of the structure rather than make an exact copy. In other words, I was a trifle lazy.